Search
MainCatalogMechanical Engineering and Machine ScienceTechnology and Equipment for Mechanical and Physico-Technical Processing
Low-plastic burnishing impact on the surface layer parameters of samples of the gas turbine engine compressor blades made of titanium alloy
Authors: Gabov I.G., Milenin A.S., Shiryaev А.А., Popova Yu.V. | Published: 21.03.2024 |
Published in issue: #4(769)/2024 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: low-plasticity burnishing, roughness and micro-hardness, residual stresses, blade microstructure, titanium blade, sample surface layer |
LSPwC influence on the surface layer parameters of the titanium alloy GTE compressor blades
Authors: Shiryaev А.А., Gabov I.G., Milenin A.S., Popova Yu.V. | Published: 06.03.2024 |
Published in issue: #3(768)/2024 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: laser shock, laser shock peening, blade surface roughness, residual compressive stresses, surface morphology, titanium alloy, blade deformation |
Features of hardware and technological process formation in obtaining the compacted carbon materials
Authors: Shubin I.N. | Published: 26.12.2023 |
Published in issue: #1(766)/2024 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: highly porous carbon material, material compaction, parameter diagnostics, rational technological modes |
Heat treatment and ion nitriding modes influence on strength properties of the high-speed steels
Authors: Buketkin B.V., Danilenko C.B. | Published: 24.11.2023 |
Published in issue: #12(765)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: high-speed steel, heat treatment, strength characteristic, impact strength, stress limit, ion nitriding |
Optimization of the turning operating conditions using exponential and polynomial equations
Authors: Grubyi S.V. | Published: 09.10.2023 |
Published in issue: #10(763)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: operating conditions, exponential equations, polynomial equations, linear programming, nonlinear programming, wear rate |
Investigation of properties of the regular structures obtained by additive technologies in combination with the powder metallurgy methods
Authors: Gordeev Y.I., Binchurov A.S., Moskvichev Е.V., Zeer G.M., Zelenkova E.G., Yasinsky V.B. | Published: 07.10.2023 |
Published in issue: #10(763)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: layered melting method, selective laser melting, regular structures, specific strength, infiltration with alloys, metal composites |
Tool and workpiece deformation effect in the cutting speed direction on the machining dynamics
Authors: Zakovorotny V.L., Gvindzhiliya V.E., Kislov K.V., Veremeev D.N. | Published: 10.08.2023 |
Published in issue: #8(761)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: dynamic cutting system, regenerative self-excitation, trajectory stability, attracting set bifurcation |
Analysis of the features of the hardware and technological design of the process of high-temperature activation of carbon material
Authors: Shubin I.N., Popova A.A. | Published: 09.08.2023 |
Published in issue: #8(761)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: high-temperature alkaline activation, synergetic effect, equipment, diagnostic researches, carbon material |
Ensuring high-quality machining of the inner surface of the electric welded pipes during deburring in the mill line
Authors: Shibanov A.V. | Published: 11.07.2023 |
Published in issue: #7(760)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: electric welded pipe, internal deburring machine rod, internal deburring tool, cutting knife, shear-bar knife |
Studying resonance characteristics of the of drawing installation oscillatory systems
Authors: Novikov Y.V., Novikov V.Y. | Published: 11.07.2023 |
Published in issue: #7(760)/2023 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: ultrasonic oscillatory systems, resonant characteristics, acoustic systems, ultrasonic equipment, drawing installations |