Search
MainCatalogMechanical Engineering and Machine ScienceTechnology and Equipment for Mechanical and Physico-Technical Processing
An Analysis of Conditions and Selection of Modes for Diamond Micro-Milling of Flat Surfaces
Authors: Grubyi S.V., Lapshin V.V. | Published: 26.07.2018 |
Published in issue: #7(700)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: micro-milling, cutting force, roughness, potassium dihydrogen phosphate, silicon, aluminum alloy |
Nonlinear Optimization of Operating Parameters of Turning by the Penalty Function Method
Authors: Grubyi S.V. | Published: 28.04.2018 |
Published in issue: #4(697)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: parametric optimization, penalty function, Newton’s method, gradient descent method, surface roughness, cutting power |
The Effect of the Creep-Feed Grinding Speed on the Morphology and Chemical Composition of the Titanium Alloy Surface
Authors: Nosenko V.A., Nosenko V.A., Koryazhkin A.A., Kremenetsky L.L. | Published: 02.04.2018 |
Published in issue: #3(696)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: titanium alloy, creep-feed grinding, grinding speed, silicon carbide, surface morphology, surface roughness |
Profiling the Flutes in Thread-Milling Cutters
Authors: Malkov O.V., Pavlyuchenkov I.A., Kozyar V.N. | Published: 30.03.2018 |
Published in issue: #3(696)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: helical flute, thread-milling cutter, profiling of the flutes, generation of geometry of the end section, grinding of the flutes |
Creating Rational Conditions for Turning Surfaces of Dissimilar Structural Materials by Brittle Superhard Cutters
Authors: Kudryashov E.A., Smirnov I.M. | Published: 21.02.2018 |
Published in issue: #2(695)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: intermittent surface, damping cutter, composite cutting material, rational contact conditions, combination of dissimilar materials, tool durability |
The Influence of New Kinematics of the Rolling Roller on the Quality of the Hardened Layer Under Surface Plastic Deformation
Authors: Zaides S.A., Ngo Cao Cuong | Published: 21.02.2018 |
Published in issue: #2(695)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: two-radial roller, deformation hardening, surface plastic deformation, surface layer quality, roughness, hardness, residual stresses |
Calculation of the Cutting Forces When Processing Plastic Materials with a Wide Range of Thicknesses of the Cutting Layer
Authors: Grubyi S.V. | Published: 21.02.2018 |
Published in issue: #2(695)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: chip formation parameters, shear angle, chip reduction coefficient, relative shear, cutting force, roughness parameters |
A Stochastic Model of Abrasive Processing. The Dynamics of Flat Grinding
Authors: Voronov S.A., Weidong Ma | Published: 23.01.2018 |
Published in issue: #1(694)/2018 | |
Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
Keywords: stochastic model, dynamics, grinding, cutting forces, vibrations, random geometry, abrasive grains, texture, machined surface |